This little guide will show how to change original image on Kathrein UFS 910 to SF Team 1.0.3

Needed tools :
USB Stick (at least 10 MB left)
Kathrein UFS 910 HDTV
A local newcs/Newcamd cardserver

1. Download this file :
2. Put the USB Stick in your PC
3. Unzip the zip file directly to the ROOT of your USB stick
4. Make sure you now have the following structure on your usb stick

/
kathrein/
ufs910/
usb_img_config_default.img
usb_img_app_20070707.img
usb_img_rootfs_20070709.img
usb_img_kernel_20070707.img
5. Remove the USB stick from your PC
6. Open up the hatch on the front of your Kathrein box, you will see 2 USB ports in the middle of the box. Insert the USB stick in one of the connectors.

7. Shut down the box by pressing the power switch on the back of the box.
8. Press MENU (on the front of the box)
9. Power on the BOX and immediatelly you will see "EMERGENCY BOOT" release the MENU button.
10. You will now see the box being flashed, with the different banks being erased and written, when the flashing procedure is finished the box will automatically reboot itself and your done.
11. Go through the initiail setup and set up your LNB's and do channel search.

A little tip, if you fail to find channels on THOR/SIRIUS/HOTBIRD/ASTRA 28.2 go back after the search to "FIRST SETUP" choose one of the sattelites and on "Test Transponder" switch between the different ones and repeat the search (worked for me).

12. Power off the received and Power it on again.
13. Notice the IP Address in the display (you will need it later so write it down on a piece of paper)

14. Now if you don't want your box to have dynamic IP (you will get an ip assigned if you have a DHCP server on your network) login to the ip address from Step 13 via telnet (login root, no password). Else skip this step

15. Open up the file /usr/etc/network/interfaces

If you want to use DHCP :
#Ethernet
auto eth0
iface eth0 inet dhcp

If you want to set a fixed ip address :

Comment out below 2 rows (auto eth0 and iface eth0 inet dhcp)

# Ethernet
#auto eth0
#iface eth0 inet dhcp

-add these rows-

auto eth0
iface eth0 inet static
address 192.168.0.24 <-- The Ip address on the box
netmask 255.255.255.0
network 192.168.0.0
broadcast 192.168.0.255
gateway 192.168.0.1 <-- Your local internet router

16. Now we need to make sure the Kathrein box can resolv dns names. Edit the file /usr/etc/resolv.conf

search lan.dreamboxx.nu
nameserver 192.10.191.30 <- Add here your ISP's DNS server
nameserver 192.10.191.31 <- Add here the secondary DNS

17. Power off the box and Power it on again.

17. Now it's time to install the Addon which enables you to use softcams in the box.

18. Unzip the file Addon_SF.tar.zip and unzip it on your computer (the file shall be named addon_200710.tar.bz2 )

19. Use any FTP client and FTP the file to the ip address of the box.

20. Transfer the file to /usr/local/etc/

21. Power off and Power on the box

22. Now it's time to connect the box to your local newcs server. Unzip radegast.zip and extract.

23. Open up radegast.cfg in an Editor (Ultraedit or Notepad++) and find this block below.

net shares = 2 <- Set to how many local Shares u have
net share 1 = 192.168.0.1:10001:2:username:password:01 02 03 04 05 06 07 08 09 10 11 12 13 14
# Comment ^IP ^PORT ^User ^Pass ^3DES

net share 2 = 192.168.0.1:10002:2:username:password:01 02 03 04 05 06 07 08 09 10 11 12 13 14
# Comment ^IP ^PORT ^User ^Pass ^3DES

Save the file.

24. Ftp over the freshly edited file to /usr/local/etc/

25. Power off and on the Box again.

If you have followed all steps in this you will NOW have picture on your packages you subscribe to from your local cardserver.

Now for to be able to find the HDTV channels for Thor do like this.
1. Press MENU
2. Choose Search Channels
3. Choose Manual Search
4. Insert Transponder 11421 H Symbol Rate : 25000 FEC : 8PSK 2/3
5. Search (Press Yes to save after channels are found)

Repeat step 4 with
11434 V Symbol rate : 25000 FEC : 8PSK 2/3
6. Search (Press Yes to save after channels are found).